← Older revision Revision as of 02:09, 13 February 2018 Line 7: Line 7:  10398 board is a 18MPix sensor front end (SFE) designed to work with [[10393]] camera system board. It has the same physical dimensions and the same optical format (1/2.3") as a 5MPix SFE [[10338D]] and 14 MPix [[10398]](15mm x 28mm). 10398 board is a 18MPix sensor front end (SFE) designed to work with [[10393]] camera system board. It has the same physical dimensions and the same optical format (1/2.3") as a 5MPix SFE [[10338D]] and 14 MPix [[10398]](15mm x 28mm).    −The 18MPix (4912×3684, 1.25μm x1.25 μm) BSI image sensor used is On Semiconductor (former Aptina) [http://www.onsemi.com/PowerSolutions/product.do?id=AR1820HS]. This sensor (and 103981 SFE) uses 4-lane HiSPi/MIPI serial interface running at 14 fps at full resolution (12bpp mode). 8-lane HiSPI mode is not supported. Other combinations of resolution/frame rate are possible.+The 18MPix (4912×3684, 1.25μm × 1.25 μm) BSI image sensor used is On Semiconductor (former Aptina) [http://www.onsemi.com/PowerSolutions/product.do?id=AR1820HS]. This sensor (and 103981 SFE) uses 4-lane HiSPi/MIPI serial interface running at 14 fps at full resolution (12bpp mode). 8-lane HiSPI mode is not supported. Other combinations of resolution/frame rate are possible.     Up to 4 103981 SFE can be directly connected to [[10393]] system board and run simultaneously at full speed (880M pixels/s combined). Up to 4 103981 SFE can be directly connected to [[10393]] system board and run simultaneously at full speed (880M pixels/s combined). Andrey.filippov

‎Supported Image Sensors

← Older revision Revision as of 02:03, 13 February 2018 Line 14: Line 14:  ** 800MHz ** 800MHz  ====Supported Image Sensors==== ====Supported Image Sensors==== −* [http://www.onsemi.com/PowerSolutions/product.do?id=MT9P006 MT9P006] - 5MPix 1/2.5" CMOS, see [[Mt9p006_specs|fps-resolution table]]+* [[10338D]]: [http://www.onsemi.com/PowerSolutions/product.do?id=MT9P006 MT9P006] -   5MPix 1/2.5" CMOS, see [[Mt9p006_specs|fps-resolution table]] −* [http://www.onsemi.com/PowerSolutions/product.do?id=MT9F002 MT9F002] - 14MPix 1/2.3" CMOS+* [[10398]]:  [http://www.onsemi.com/PowerSolutions/product.do?id=MT9F002 MT9F002] -   14MPix 1/2.3" CMOS  +* [[103981]]: [http://www.onsemi.com/PowerSolutions/product.do?id=AR1820HS AR1820HS] - 18MPix 1/2.3" CMOS BSI ('' not yet manufactured'')     ====Memory and Storage==== ====Memory and Storage==== Andrey.filippov

← Older revision Revision as of 01:42, 13 February 2018 (One intermediate revision by the same user not shown)Line 7: Line 7:  10398 board is a 18MPix sensor front end (SFE) designed to work with [[10393]] camera system board. It has the same physical dimensions and the same optical format (1/2.3") as a 5MPix SFE [[10338D]] and 14 MPix [[10398]](15mm x 28mm). 10398 board is a 18MPix sensor front end (SFE) designed to work with [[10393]] camera system board. It has the same physical dimensions and the same optical format (1/2.3") as a 5MPix SFE [[10338D]] and 14 MPix [[10398]](15mm x 28mm).    −The 18MPix (4912×3684, 1.25μm x1.25 μm) BSI image sensor used is On Semiconductor (former Aptina) [http://www.onsemi.com/PowerSolutions/product.do?id=AR1820HS]. This sensor (and 103981 SFE) uses 4-lane HiSPi/MIPI serial interface running at 14 fps at full resolution (12bpp mode). 8-lane HiSPI mode is not supported, mode Other combinations of resolution/frame rate are possible.+The 18MPix (4912×3684, 1.25μm x1.25 μm) BSI image sensor used is On Semiconductor (former Aptina) [http://www.onsemi.com/PowerSolutions/product.do?id=AR1820HS]. This sensor (and 103981 SFE) uses 4-lane HiSPi/MIPI serial interface running at 14 fps at full resolution (12bpp mode). 8-lane HiSPI mode is not supported. Other combinations of resolution/frame rate are possible.     Up to 4 103981 SFE can be directly connected to [[10393]] system board and run simultaneously at full speed (880M pixels/s combined). Up to 4 103981 SFE can be directly connected to [[10393]] system board and run simultaneously at full speed (880M pixels/s combined).    −103981 SFE uses the same 30-pin flex cable connector for control (I²C, extra GPIO), differential data output (4-lane HiSPi+clock) and 3.3V power (additional 2.8V analog and 1.8V digital are generated on board). Short connections can use general purpose flex jumpers (30 conductors, 0.5mm pitch) or Elphel flex cables manufactured for the parallel interface sensors, longer connections require controlled-impedance flex cables with 100Ω differential lines.+103981 SFE uses the same 30-pin flex cable connector for control (I²C, extra GPIO), differential data output (4-lane HiSPi+clock) and 3.3V power (additional 2.8V analog, 1.8V digital, and 1.2V digital are generated on board). Short connections can use general purpose flex jumpers (30 conductors, 0.5mm pitch) or Elphel flex cables manufactured for the parallel interface sensors, longer connections require controlled-impedance flex cables with 100Ω differential lines.     [[Media:103981_sch.pdf|103981 Circuit Diagram]] <br/> [[Media:103981_gerber.tar.gz|103981 Gerber files]] <br/>[[Media:103981_assy.tar.gz|103981 placement files]] [[Media:103981_sch.pdf|103981 Circuit Diagram]] <br/> [[Media:103981_gerber.tar.gz|103981 Gerber files]] <br/>[[Media:103981_assy.tar.gz|103981 placement files]] Andrey.filippov

Created page with "==103981== ''This board is not manufactured yet, images will be updated'' thumb|374px|10398 board, top view (will be replaced with 103981) Image:103..."

New page

==103981==
''This board is not manufactured yet, images will be updated''

[[Image:10398_top.png|thumb|374px|10398 board, top view (will be replaced with 103981)]]
[[Image:10398_bottom.png|thumb|374px|10398 board, bottom view (will be replaced with 103981)]]

10398 board is a 18MPix sensor front end (SFE) designed to work with [[10393]] camera system board. It has the same physical dimensions and the same optical format (1/2.3") as a 5MPix SFE [[10338D]] and 14 MPix [[10398]](15mm x 28mm).

The 18MPix (4912×3684, 1.25μm x1.25 μm) BSI image sensor used is On Semiconductor (former Aptina) [http://www.onsemi.com/PowerSolutions/product.do?id=AR1820HS]. This sensor (and 103981 SFE) uses 4-lane HiSPi/MIPI serial interface running at 14 fps at full resolution (12bpp mode). 8-lane HiSPI mode is not supported, mode Other combinations of resolution/frame rate are possible.

Up to 4 103981 SFE can be directly connected to [[10393]] system board and run simultaneously at full speed (880M pixels/s combined).

103981 SFE uses the same 30-pin flex cable connector for control (I²C, extra GPIO), differential data output (4-lane HiSPi+clock) and 3.3V power (additional 2.8V analog and 1.8V digital are generated on board). Short connections can use general purpose flex jumpers (30 conductors, 0.5mm pitch) or Elphel flex cables manufactured for the parallel interface sensors, longer connections require controlled-impedance flex cables with 100Ω differential lines.

[[Media:103981_sch.pdf|103981 Circuit Diagram]] <br/> [[Media:103981_gerber.tar.gz|103981 Gerber files]] <br/>[[Media:103981_assy.tar.gz|103981 placement files]] Andrey.filippov

← Older revision Revision as of 01:34, 13 February 2018 Line 5: Line 5:  10398 board is a 14MPix sensor front end (SFE) designed to work with [[10393]] camera system board. It has the same physical dimensions and the same optical format (1/2.3") as a 5MPix SFE [[10338D]] (15mm x 28mm). 10398 board is a 14MPix sensor front end (SFE) designed to work with [[10393]] camera system board. It has the same physical dimensions and the same optical format (1/2.3") as a 5MPix SFE [[10338D]] (15mm x 28mm).    −The 14MPix (4608H x 3288V, 1.4μm x1.4 μm) image sensor used is On Semiconductor (former Aptina) [http://www.onsemi.com/pub_link/Collateral/MT9F002-D.PDF MT9F002]. This sensor (and 10398 SFE) uses 4-lane HiSPi serial interface running at 700 Mpbs/lane and is capable of running at 13.7 fps at full resolution (12bpp mode), or 60fps at 2304x1296 (1080p + 20% EIS). Other combinations of resolution/frame rate are possible.+The 14MPix (4608H x 3288V, 1.4μm x1.4 μm) image sensor used is On Semiconductor (former Aptina) [http://www.onsemi.com/pub_link/Collateral/MT9F002-D.PDF MT9F002]. This sensor (and 10398 SFE) uses 4-lane HiSPi serial interface running at 700 Mbps/lane and is capable of running at 13.7 fps at full resolution (12bpp mode), or 60fps at 2304x1296 (1080p + 20% EIS). Other combinations of resolution/frame rate are possible.     Up to 4 10398 SFE can be directly connected to [[10393]] system board and run simultaneously at full speed (880M pixels/s combined). Up to 4 10398 SFE can be directly connected to [[10393]] system board and run simultaneously at full speed (880M pixels/s combined). Andrey.filippov

Andrey.filippov uploaded File:103981 assy.tar.gz

New page

== Licensing ==
{{CERN OHLv1.1 }} Andrey.filippov

Andrey.filippov uploaded File:103981 gerber.tar.gz

New page

== Licensing ==
{{CERN OHLv1.1 }} Andrey.filippov

Andrey.filippov uploaded File:103981 sch.pdf

New page

== Licensing ==
{{CERN OHLv1.1 }} Andrey.filippov

AndreyFilippov committed changes to the Elphel git project :
comment typo

AndreyFilippov committed changes to the Elphel git project :
committed x393_hispi.bit (v1704_fb) corresponding to the previous source commit

AndreyFilippov committed changes to the Elphel git project :
Merge branch 'master' of git@git.elphel.com:Elphel/x393.git

AndreyFilippov committed changes to the Elphel git project :
HISPI: added per-lane line-sync monitoring, TRIG as programmable option for GP0 and GP1

AndreyFilippov committed changes to the Elphel git project :
another wrapper

‎Example file

← Older revision Revision as of 01:00, 10 February 2018 (2 intermediate revisions by the same user not shown)Line 84: Line 84:     ==<font color="blue">JP4</font>== ==<font color="blue">JP4</font>==  +===Example file===  + Download [https://community.elphel.com/pictures/test.jp4 sample]  {| {|  |[[File:Jp4 example rotated asjpeg.jpeg|200px|thumb|JP4 opened as JPEG, rotated 90&deg;]] |[[File:Jp4 example rotated asjpeg.jpeg|200px|thumb|JP4 opened as JPEG, rotated 90&deg;]] Line 89: Line 91:  |} |}  * If opened as a normal image the macro blocks will be displayed as 8x32. * If opened as a normal image the macro blocks will be displayed as 8x32.  +  ===Online=== ===Online===  * [https://community.elphel.com/jp4viewer/?width=800&quality=1 Online JP4 viewer] * [https://community.elphel.com/jp4viewer/?width=800&quality=1 Online JP4 viewer] Line 367: Line 370:     Example files: Example files: −* [http://community.elphel.com/files/jp4/example_JP4.jpeg Example JP4]+* [http://community.elphel.com/files/jp4/example_JP46.jpeg Example JP46]  * [http://community.elphel.com/files/jp4/example_flipped.dng Example DNG] * [http://community.elphel.com/files/jp4/example_flipped.dng Example DNG]  * [http://community.elphel.com/files/jp4/example_converted.jpg Example JPG (converted)] * [http://community.elphel.com/files/jp4/example_converted.jpg Example JPG (converted)] Oleg

Oleg Dzhimiev committed changes to the Elphel git project :
filled table for pages

Oleg Dzhimiev committed changes to the Elphel git project :
frequency and voltage for 14MPx

AndreyFilippov committed changes to the Elphel git project :
Merge branch 'master' of git.elphel.com:Elphel/x393

AndreyFilippov committed changes to the Elphel git project :
generated hispi bitstream with 15.3

Oleg Dzhimiev committed changes to the Elphel git project :
init for 14MPx

Oleg Dzhimiev committed changes to the Elphel git project :
initial changes to dynamic page registering and sensors with 16 bit register addresses