Wiki Recent Changes

Microzed issues

Fri, 02/19/2016 - 18:19

← Older revision Revision as of 01:19, 20 February 2016 (One intermediate revision not shown)Line 1: Line 1: ==List== ==List== -* [SOLVED] UART+===[SOLVED] UART=== Description: Description: Line 31: Line 31: -* SSH terminal+===SSH terminal=== Description: Description: Line 38: Line 38: Bad network cable? Network problem? Bad network cable? Network problem? -* RTC+===RTC=== - Too many messages when rtc is missing+ Not an issue + "hwclock: can't open '/dev/misc/rtc': No such file or directory" repeated 3 times Description: Description: 3x"hwclock: can't open '/dev/misc/rtc': No such file or directory" in boot log 3x"hwclock: can't open '/dev/misc/rtc': No such file or directory" in boot log Possible reason: Possible reason: - driver+ a. Microzed doesn't have a real-time clock (rtc) + b. Reported by /etc/init.d/hwclock.sh - not the driver -* U-boot Falcon mode (boot from SPL directly to OS avoiding full u-boot)+===U-boot Falcon mode (boot from SPL directly to OS avoiding full u-boot)=== Description: Description: Line 53: Line 55: Possible reason: Possible reason: -* U-boot spl reads u-boot-dtb.img 2 times+===U-boot spl reads u-boot-dtb.img 2 times=== Description: Description: Line 92: Line 94: - -* hwclock multiple error messages - - Description: - Not an issue - "hwclock: can't open '/dev/misc/rtc': No such file or directory" repeated 3 times - Possible reason: - a. Microzed doesn't have a real-time clock (rtc) - b. Reported by /etc/init.d/hwclock.sh - not the driver ==Useful pages== ==Useful pages== Oleg

Poky 2.0 manual

Fri, 02/19/2016 - 18:13

Setup:

← Older revision Revision as of 01:13, 20 February 2016 Line 41: Line 41: git clone -b master https://github.com/Elphel/meta-elphel393.git meta-elphel393 git clone -b master https://github.com/Elphel/meta-elphel393.git meta-elphel393 - cd meta-elphel393; git checkout e8c6e139848a21b1bf0c05b306108e390bc44e24; cd ..+ cd meta-elphel393; git checkout c5237f99d94217bff8c9180bed93ee673c9590a1; cd .. git clone -b master https://github.com/Xilinx/meta-xilinx.git meta-xilinx git clone -b master https://github.com/Xilinx/meta-xilinx.git meta-xilinx Oleg

Microzed issues

Fri, 02/19/2016 - 18:07

New page

==List==
* [SOLVED] UART

Description:
UART register contents: timeout=0 rxfifo_level=56, should be timeout=10 rxfifo_level=56
minicom prints 56 symbols at a time when rxfifo reaches its level.
remembers all typed symbols
sometimes the timeout register is set correctly
Possible reason:
In driver .startup and .termios conflict? Racing Resets or reset takes time?
Solution:
Added a delay after reset - some other functions in the driver also have it - some not. Luck?
Patch:
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index f214c7f..164e32d 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -704,6 +704,9 @@ static void cdns_uart_set_termios(struct uart_port *port,
ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);

+ while (cdns_uart_readl(CDNS_UART_CR_OFFSET) &
+ (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
+ cpu_relax();
/*
* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
Links:
* https://forums.xilinx.com/t5/Zynq-All-Programmable-SoC/Zynq-Uart-timeout-problem/td-p/432016
* http://www.makelinux.net/ldd3/chp-7-sect-3


* SSH terminal

Description:
Freezes, lags but remembers all typed symbols
Possible reason:
Bad network cable? Network problem?

* RTC

Too many messages when rtc is missing
Description:
3x"hwclock: can't open '/dev/misc/rtc': No such file or directory" in boot log
Possible reason:
driver


* U-boot Falcon mode (boot from SPL directly to OS avoiding full u-boot)

Description:
Try
Possible reason:

* U-boot spl reads u-boot-dtb.img 2 times

Description:
Not an issue - prints "reading u-boot-dtb.img" 2 times. "Very Annoying","Every microsecond counts"!
Possible reason:
u-boot/common/spl/spl_fat.c:
int spl_load_image_fat(block_dev_desc_t *block_dev,
int partition,
const char *filename)
{
int err;
struct image_header *header;

err = spl_register_fat_device(block_dev, partition);
if (err)
goto end;

header = (struct image_header *)(CONFIG_SYS_TEXT_BASE -
sizeof(struct image_header));

err = file_fat_read(filename, header, sizeof(struct image_header));
if (err <= 0)
goto end;

spl_parse_image_header(header);

err = file_fat_read(filename, (u8 *)spl_image.load_addr, 0);

end:
#ifdef CONFIG_SPL_LIBCOMMON_SUPPORT
if (err <= 0)
printf("%s: error reading image %s, err - %d\n",
__func__, filename, err);
#endif

return (err <= 0);
}



* hwclock multiple error messages

Description:
Not an issue
"hwclock: can't open '/dev/misc/rtc': No such file or directory" repeated 3 times
Possible reason:
a. Microzed doesn't have a real-time clock (rtc)
b. Reported by /etc/init.d/hwclock.sh - not the driver

==Useful pages==
* http://processors.wiki.ti.com/index.php/Enabling_Stack_Dumping_in_Linux_Kernel
* https://lists.yoctoproject.org/pipermail/poky/2015-February/010037.html - change hostname in poky
* http://www.makelinux.net/ldd3/chp-7-sect-3
* http://www.denx.de/wiki/pub/U-Boot/MiniSummitELCE2013/2013-ELCE-U-Boot-Falcon-Boot.pdf Oleg

Microzed issues

Fri, 02/19/2016 - 17:46

New page

==List==
* [SOLVED] UART

Description:
UART register contents: timeout=0 rxfifo_level=56, should be timeout=10 rxfifo_level=56
minicom prints 56 symbols at a time when rxfifo reaches its level.
remembers all typed symbols
sometimes the timeout register is set correctly
Possible reason:
In driver .startup and .termios conflict? Racing Resets or reset takes time?
Solution:
Added a delay after reset - some other functions in the driver also have it - some not. Luck?
Patch:
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index f214c7f..164e32d 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -704,6 +704,9 @@ static void cdns_uart_set_termios(struct uart_port *port,
ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);

+ while (cdns_uart_readl(CDNS_UART_CR_OFFSET) &
+ (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
+ cpu_relax();
/*
* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
Links:
* https://forums.xilinx.com/t5/Zynq-All-Programmable-SoC/Zynq-Uart-timeout-problem/td-p/432016
* http://www.makelinux.net/ldd3/chp-7-sect-3


* SSH terminal

Description:
Freezes, lags but remembers all typed symbols
Possible reason:
Bad network cable? Network problem?

* RTC

Too many messages when rtc is missing
Description:
3x"hwclock: can't open '/dev/misc/rtc': No such file or directory" in boot log
Possible reason:
driver


* U-boot Falcon mode (boot from SPL directly to OS avoiding full u-boot)

Description:
Try
Possible reason:

* U-boot spl reads u-boot-dtb.img 2 times

Description:
Not an issue - prints "reading u-boot-dtb.img" 2 times. "Very Annoying","Every microsecond counts"!
Possible reason:
u-boot/common/spl/spl_fat.c:
int spl_load_image_fat(block_dev_desc_t *block_dev,
int partition,
const char *filename)
{
int err;
struct image_header *header;

err = spl_register_fat_device(block_dev, partition);
if (err)
goto end;

header = (struct image_header *)(CONFIG_SYS_TEXT_BASE -
sizeof(struct image_header));

err = file_fat_read(filename, header, sizeof(struct image_header));
if (err <= 0)
goto end;

spl_parse_image_header(header);

err = file_fat_read(filename, (u8 *)spl_image.load_addr, 0);

end:
#ifdef CONFIG_SPL_LIBCOMMON_SUPPORT
if (err <= 0)
printf("%s: error reading image %s, err - %d\n",
__func__, filename, err);
#endif

return (err <= 0);
}



==Useful pages==
* http://processors.wiki.ti.com/index.php/Enabling_Stack_Dumping_in_Linux_Kernel
* https://lists.yoctoproject.org/pipermail/poky/2015-February/010037.html - change hostname in poky
* http://www.makelinux.net/ldd3/chp-7-sect-3
* http://www.denx.de/wiki/pub/U-Boot/MiniSummitELCE2013/2013-ELCE-U-Boot-Falcon-Boot.pdf Oleg

Microzed issues

Fri, 02/19/2016 - 16:34

New page

==List==
* [SOLVED] UART

Description:
UART register contents: timeout=0 rxfifo_level=56, should be timeout=10 rxfifo_level=56
minicom prints 56 symbols at a time when rxfifo reaches its level.
remembers all typed symbols
sometimes the timeout register is set correctly
Possible reason:
In driver .startup and .termios conflict? Racing Resets or reset takes time?
Solution:
Added a delay after reset - some other functions in the driver also have it - some not. Luck?
Patch:
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index f214c7f..164e32d 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -704,6 +704,9 @@ static void cdns_uart_set_termios(struct uart_port *port,
ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);

+ while (cdns_uart_readl(CDNS_UART_CR_OFFSET) &
+ (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
+ cpu_relax();
/*
* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
Links:
* https://forums.xilinx.com/t5/Zynq-All-Programmable-SoC/Zynq-Uart-timeout-problem/td-p/432016
* http://www.makelinux.net/ldd3/chp-7-sect-3


* SSH terminal

Description:
Freezes, lags but remembers all typed symbols
Possible reason:
Bad network cable? Network problem?

* RTC

Too many messages when rtc is missing
Description:
3x"hwclock: can't open '/dev/misc/rtc': No such file or directory" in boot log
Possible reason:
driver


* U-boot Falcon mode (boot from SPL directly to OS avoiding full u-boot)

Description:
Try
Possible reason:

* U-boot spl reads u-boot-dtb.img 2 times

Description:
Not an issue - prints "reading u-boot-dtb.img" 2 times. "Very Annoying","Every microsecond counts"!
Possible reason:
u-boot/common/spl/spl_fat.c:
int spl_load_image_fat(block_dev_desc_t *block_dev,
int partition,
const char *filename)
{
int err;
struct image_header *header;

err = spl_register_fat_device(block_dev, partition);
if (err)
goto end;

header = (struct image_header *)(CONFIG_SYS_TEXT_BASE -
sizeof(struct image_header));

err = file_fat_read(filename, header, sizeof(struct image_header));
if (err <= 0)
goto end;

spl_parse_image_header(header);

err = file_fat_read(filename, (u8 *)spl_image.load_addr, 0);

end:
#ifdef CONFIG_SPL_LIBCOMMON_SUPPORT
if (err <= 0)
printf("%s: error reading image %s, err - %d\n",
__func__, filename, err);
#endif

return (err <= 0);
}



==Useful pages==
* http://processors.wiki.ti.com/index.php/Enabling_Stack_Dumping_in_Linux_Kernel
* https://lists.yoctoproject.org/pipermail/poky/2015-February/010037.html - change hostname in poky
* http://www.makelinux.net/ldd3/chp-7-sect-3 Oleg

Microzed issues

Fri, 02/19/2016 - 15:28

New page

==List==
* [SOLVED] UART

Description:
UART register contents: timeout=0 rxfifo_level=56, should be timeout=10 rxfifo_level=56
minicom prints 56 symbols at a time when rxfifo reaches its level.
remembers all typed symbols
sometimes the timeout register is set correctly
Possible reason:
In driver .startup and .termios conflict? Racing Resets or reset takes time?
Solution:
Added a delay after reset - some other functions in the driver also have it - some not. Luck?
Patch:
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index f214c7f..164e32d 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -704,6 +704,9 @@ static void cdns_uart_set_termios(struct uart_port *port,
ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);

+ while (cdns_uart_readl(CDNS_UART_CR_OFFSET) &
+ (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
+ cpu_relax();
/*
* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
Links:
* https://forums.xilinx.com/t5/Zynq-All-Programmable-SoC/Zynq-Uart-timeout-problem/td-p/432016
* http://www.makelinux.net/ldd3/chp-7-sect-3


* SSH terminal

Description:
Freezes, lags but remembers all typed symbols
Possible reason:
Bad network cable? Network problem?

* RTC

Too many messages when rtc is missing
Description:
3x"hwclock: can't open '/dev/misc/rtc': No such file or directory" in boot log
Possible reason:
driver


* U-boot Falcon mode (boot from SPL directly to OS avoiding full u-boot)

Description:
Try
Possible reason:



==Useful pages==
* http://processors.wiki.ti.com/index.php/Enabling_Stack_Dumping_in_Linux_Kernel
* https://lists.yoctoproject.org/pipermail/poky/2015-February/010037.html - change hostname in poky
* http://www.makelinux.net/ldd3/chp-7-sect-3 Oleg

Microzed issues

Fri, 02/19/2016 - 14:09

New page

==List==
* [SOLVED] UART

Description:
UART register contents: timeout=0 rxfifo_level=56, should be timeout=10 rxfifo_level=56
minicom prints 56 symbols at a time when rxfifo reaches its level.
remembers all typed symbols
sometimes the timeout register is set correctly
Possible reason:
In driver .startup and .termios conflict? Racing Resets or reset takes time?
Solution:
Added a delay after reset - some other functions in the driver also have it - some not. Luck?
Patch:
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index f214c7f..164e32d 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -704,6 +704,9 @@ static void cdns_uart_set_termios(struct uart_port *port,
ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);

+ while (cdns_uart_readl(CDNS_UART_CR_OFFSET) &
+ (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
+ cpu_relax();
/*
* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
Links:
* https://forums.xilinx.com/t5/Zynq-All-Programmable-SoC/Zynq-Uart-timeout-problem/td-p/432016
* http://www.makelinux.net/ldd3/chp-7-sect-3


* SSH terminal

Description:
Freezes, lags but remembers all typed symbols
Possible reason:
Bad network cable? Network problem?

* RTC

Too many messages when rtc is missing
Description:
3x"hwclock: can't open '/dev/misc/rtc': No such file or directory" in boot log
Possible reason:
driver


==Useful pages==
* http://processors.wiki.ti.com/index.php/Enabling_Stack_Dumping_in_Linux_Kernel
* https://lists.yoctoproject.org/pipermail/poky/2015-February/010037.html - change hostname in poky
* http://www.makelinux.net/ldd3/chp-7-sect-3 Oleg

Microzed issues

Thu, 02/18/2016 - 21:13

New page

==List==
* UART

Description:
UART register contents: timeout=0 rxfifo_level=56, should be timeout=10 rxfifo_level=56
minicom prints 56 symbols at a time when rxfifo reaches its level.
remembers all typed symbols
sometimes the timeout register is set correctly
Possible reason:
In driver .startup and .termios conflict?

* SSH terminal

Description:
Freezes, lags but remembers all typed symbols
Possible reason:
UART problem?

* RTC

Too many messages when rtc is missing
Description:
3x"hwclock: can't open '/dev/misc/rtc': No such file or directory" in boot log
Possible reason:
driver


==Useful pages==
* https://forums.xilinx.com/t5/Zynq-All-Programmable-SoC/Zynq-Uart-timeout-problem/td-p/432016
* http://processors.wiki.ti.com/index.php/Enabling_Stack_Dumping_in_Linux_Kernel
* https://lists.yoctoproject.org/pipermail/poky/2015-February/010037.html
* http://www.makelinux.net/ldd3/chp-7-sect-3 Oleg

Microzed issues

Thu, 02/18/2016 - 19:33

New page

==List==
* UART

Description:
UART register contents: timeout=0 rxfifo_level=56, should be timeout=10 rxfifo_level=56
minicom prints 56 symbols at a time when rxfifo reaches its level.
remembers all typed symbols
sometimes the timeout register is set correctly
Possible reason:
In driver .startup and .termios conflict?

* SSH terminal

Description:
Freezes, lags but remembers all typed symbols
Possible reason:
UART problem?

* RTC

Too many messages when rtc is missing
Description:
3x"hwclock: can't open '/dev/misc/rtc': No such file or directory" in boot log
Possible reason:
driver
 Oleg

Poky 2.0 manual

Thu, 02/18/2016 - 15:08

← Older revision Revision as of 22:08, 18 February 2016 (One intermediate revision not shown)Line 15: Line 15: These names are listed as they appear in the u-boot configuration header file - actual output files have different names: These names are listed as they appear in the u-boot configuration header file - actual output files have different names: -* '''boot.bin'''+('''u-boot-dtb.img''') - u-boot as the first stage bootloader = Secondary Program Loader that boots '''u-boot-dtb.img'''+* '''boot.bin''' - u-boot as the first stage bootloader = Secondary Program Loader that boots '''u-boot-dtb.img''' +* '''u-boot-dtb.img''' - full size u-boot with a stripped device tree (''cat u-boot.img some_stripped_devicetree.dtb > u-boot-dtb.img'') * '''devicetree.dtb''' - device tree with described interfaces, zynq registers, interrupts and drivers * '''devicetree.dtb''' - device tree with described interfaces, zynq registers, interrupts and drivers * '''uImage''' - kernel, drivers * '''uImage''' - kernel, drivers Line 40: Line 41: git clone -b master https://github.com/Elphel/meta-elphel393.git meta-elphel393 git clone -b master https://github.com/Elphel/meta-elphel393.git meta-elphel393 - cd meta-elphel393; git checkout 2bf73c48be5433002144bc9126bdc9c44b30b98c; cd ..+ cd meta-elphel393; git checkout e8c6e139848a21b1bf0c05b306108e390bc44e24; cd .. git clone -b master https://github.com/Xilinx/meta-xilinx.git meta-xilinx git clone -b master https://github.com/Xilinx/meta-xilinx.git meta-xilinx Oleg

Poky 2.0 manual

Wed, 02/17/2016 - 12:19

← Older revision Revision as of 19:19, 17 February 2016 Line 40: Line 40: git clone -b master https://github.com/Elphel/meta-elphel393.git meta-elphel393 git clone -b master https://github.com/Elphel/meta-elphel393.git meta-elphel393 - cd meta-elphel393; git checkout 2bf73c48be5433002144bc9126bdc9c44b30b98c; cd ..+ cd meta-elphel393; git checkout e8c6e139848a21b1bf0c05b306108e390bc44e24; cd .. git clone -b master https://github.com/Xilinx/meta-xilinx.git meta-xilinx git clone -b master https://github.com/Xilinx/meta-xilinx.git meta-xilinx Oleg

Elphel 353 series quick start guide

Thu, 02/11/2016 - 13:13

Command line access:

← Older revision Revision as of 20:13, 11 February 2016 Line 117: Line 117: ==Command line access== ==Command line access== -a) '''SSH'''+a) '''SSH''' (outdated, drops connections, please, use Telnet) In the terminal window: ssh root@192.168.0.9 In the terminal window: ssh root@192.168.0.9 Oleg

Request for quote 393-1

Tue, 02/09/2016 - 15:59

Created page with "Elphel, Inc. invites the machine shops to Quote manufacturing of the following parts: {| class="wikitable" style="background:#fcfcfc; " border="1" |+ Metal Parts |- ! Part !! Q..."

New page

Elphel, Inc. invites the machine shops to Quote manufacturing of the following parts:
{| class="wikitable" style="background:#fcfcfc; " border="1"
|+ Metal Parts
|-
! Part !! QTY per Unit !! Notes
|-
| [[Elphel_camera_parts_0393-12#0393-12-29_-_Sensor_front_end.2C_CS-mount|0393-12-29 - Sensor front end, CS-mount ]] || 10 || 100 ||
|-
| [[Elphel_camera_parts_0393-12#0393-12-30_-_Sensor_adjustment_plate|0393-12-30 - Sensor adjustment plate ]] || 10 || 100 ||
|-
| [[Elphel_camera_parts_0393-11#0393-11-04_-_Cooling_fan_enclosure|0393-11-04 - Cooling fan enclosure ]] || 10 || 100 ||
|-
| [[Elphel_camera_parts_0393-11#0393-11-10_-_CPU_heat_plate|0393-11-10 - CPU heat plate]] || 10 || 100 ||
|-
| [[Elphel_camera_parts_0393-18#0353-18-30_-_tripod_mount_nut.2C_1.2F4-20_thread|0353-18-30 - tripod mount nut, 1/4-20 thread ]] || 10 || 100 ||
|-
| [[Elphel_camera_parts_0393-18#0353-18-31_-_tripod_mount_plate|0353-18-31 - tripod mount plate ]] || 10 || 100||
|-
|}

Please, read the [[Supplier_Terms_and_Conditions|Suppliers Terms and Conditions]] and send the Proposals by e-mail: [mailto://supplies@elphel.com supplies@elphel.com] Olga

Poky 2.0 manual

Mon, 02/01/2016 - 16:25

Setup:

← Older revision Revision as of 23:25, 1 February 2016 Line 40: Line 40: git clone -b master https://github.com/Elphel/meta-elphel393.git meta-elphel393 git clone -b master https://github.com/Elphel/meta-elphel393.git meta-elphel393 - cd meta-elphel393; git checkout 9013e39faac2f99c8dda36244ae8a111c72214e1; cd ..+ cd meta-elphel393; git checkout 2bf73c48be5433002144bc9126bdc9c44b30b98c; cd .. git clone -b master https://github.com/Xilinx/meta-xilinx.git meta-xilinx git clone -b master https://github.com/Xilinx/meta-xilinx.git meta-xilinx Oleg

Eyesis4Pi

Mon, 02/01/2016 - 15:30

← Older revision Revision as of 22:30, 1 February 2016 Line 1: Line 1: - == [[Image:hp_banner_eyesis.png]] == == [[Image:hp_banner_eyesis.png]] == Oleg

Price list

Mon, 02/01/2016 - 15:29

← Older revision Revision as of 22:29, 1 February 2016 Line 1: Line 1: -+ = Ordering = = Ordering = Oleg

Poky 2.0 manual

Sun, 01/31/2016 - 18:53

Setup:

← Older revision Revision as of 01:53, 1 February 2016 Line 46: Line 46: git clone -b master git://git.openembedded.org/meta-openembedded meta-openembedded git clone -b master git://git.openembedded.org/meta-openembedded meta-openembedded - cd meta-openembedded; git checkout 3d2c0f5902cacf9d8544bf263b51ef0dd1a7218c; cd ..+ cd meta-openembedded; git checkout 73854a05565b30a5ca146ac53959c679b27815aa; cd .. '''#Part 2 : init environment and auto-fill Yocto's conf-files''' '''#Part 2 : init environment and auto-fill Yocto's conf-files''' Oleg

Eyesis4Pi

Sun, 01/31/2016 - 01:16

← Older revision Revision as of 08:16, 31 January 2016 Line 1: Line 1: -50% off on the current Eyesis4Pi camera model!+ == [[Image:hp_banner_eyesis.png]] == == [[Image:hp_banner_eyesis.png]] == Oleg

Price list

Sun, 01/31/2016 - 01:15

← Older revision Revision as of 08:15, 31 January 2016 (One intermediate revision not shown)Line 1: Line 1: -= Info =+ = Ordering = = Ordering = Oleg

Price list

Fri, 01/29/2016 - 17:22

← Older revision Revision as of 00:22, 30 January 2016 Line 1: Line 1: -= Info = 50% off on the current Eyesis4Pi camera model! 50% off on the current Eyesis4Pi camera model! * Due to development of the new 10393 camera series all current models including Eyesis4Pi are offered at 50% discount while supply lasts * Due to development of the new 10393 camera series all current models including Eyesis4Pi are offered at 50% discount while supply lasts Oleg

Secondary menu

Elphel Development Blog

Elphel GIT logs

Elphel CVS logs

Who's online

Microzed issues

Poky 2.0 manual

Microzed issues

Microzed issues

Microzed issues

Microzed issues

Microzed issues

Microzed issues

Microzed issues

Poky 2.0 manual

Poky 2.0 manual

Elphel 353 series quick start guide

Request for quote 393-1

Poky 2.0 manual

Eyesis4Pi

Price list

Poky 2.0 manual

Eyesis4Pi

Price list

Price list

Pages