10349

From ElphelWiki
Revision as of 07:27, 12 October 2007 by Dimon (talk | contribs)
Jump to: navigation, search

Russia page 10349.Ru

Elphel 10349RevC boaard
1.8" IDE HD with zif connector
10349 RevC mounted on 10353

Interface board.

  • serial port
  • 4 ports USB hub with 3 internal, 1 external USB ports
  • IDE port for the 1.8" hard drive with ZIF Flat cable
  • 2 socket for external usermade board
  • some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

Connector pinouts

 internal USB2, USB3, USB4
   1 - power
   2 - D-
   3 - D+
   4 - GND
 J7 is the serial port
   1 - RX
   2 - TX
   3 - CTS
   4 - RTS
   5 - GND
   6 - removed, used as key
 J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.
 J5 for connect external boards
   1 - EXT0 (FPGA IO signal)
   2 - EXT1 (FPGA IO signal)
   3 - EXT2 (FPGA IO signal)
   4 - EXT3 (FPGA IO signal)
   5 - EXT4 (FPGA IO signal)
   6 - GND
   7 - EXT5 (FPGA IO signal)
   8 - GND
   9 - +3.3V
   10 - +3.3V
   11 - CTS (TTL level)
   12 - RTS (TTL level)
   13 - RX (TTL level)
   14 - TX (TTL level)
   15 - not connected
   16 - not connected

Power description

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

Power consumption in different configurations

Here are some results on power consumption test made in different configurations with Elphel 353 camera, 5MPix sensor, 10349 board, 1,8" HD and USB staff...

2400 milliwattsjust booted
3000 milliwattsafter setting image parameters
3700 milliwattsstreamer on
3300 milliwattsstreamer off
3800 milliwattsstreamer on and somebody playing the stream
5000 milliwattswith streamer on and HD writing at full speed (dd)
5800 milliwattsstreamer on, HD and USB-flash writing at full speed
3300 milliwattsback to streamer off

Tests was performed with Linksys SRW224P POE switch

Kit for Developers

  • for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
  • for internal USB sockets - AE10179-ND (Digi-Key) - 1
  • for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
  • or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
  • blank PCB board V1255-ND (Digi-Key) - 1

Next revision

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [JM20330] (send email, no answer)
* Marvell [88i8030, 88SA8040] (need sign NDA, sucks)
* Silicon Image [SiI3611] (Available only through your local sales contact. send email, no answer)
* Atmel [AT78C5010] (Available only through your local sales contact. send email, no answer)
* ACARD [ARC-770] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. These are big secrets of the companies :(

Body of camera for developers

Case A consist of a large window on the top and transparent plex panel for closing. Anybody can easy modified this panel for any application.

Case B consist a large space with two bodies. Can use same as back pannel can use for backpanel plex too.


Body for developers kit A
Body for developers kit B